Materialeinstellungen für Thunderlaser (Wien): Unterschied zwischen den Versionen
Zur Navigation springen
Zur Suche springen
Roland (Diskussion | Beiträge) |
|||
| (21 dazwischenliegende Versionen von 9 Benutzern werden nicht angezeigt) | |||
| Zeile 28: | Zeile 28: | ||
| cut | | cut | ||
| 60 | | 60 | ||
| − | | | + | | 90 |
| | | | ||
|- | |- | ||
| Zeile 35: | Zeile 35: | ||
| engrave | | engrave | ||
| 20 | | 20 | ||
| − | | | + | | 90 |
| | | | ||
|- | |- | ||
| Zeile 76: | Zeile 76: | ||
| Graupappe (2mm) | | Graupappe (2mm) | ||
| cut | | cut | ||
| − | | | + | | 90 |
| − | | | + | | 14 |
| + | | | ||
| + | |- | ||
| + | |||
| + | | Graupappe (2mm) | ||
| + | | engrave | ||
| + | | 20 | ||
| + | | 90 | ||
| | | | ||
|- | |- | ||
| Zeile 89: | Zeile 96: | ||
| − | | Graupappe | + | | Graupappe (3mm) |
| cut | | cut | ||
| + | | 90 | ||
| + | | 12 | ||
| | | | ||
| − | | | + | |- |
| + | |||
| + | |||
| + | | Graupappe (4mm) | ||
| + | | cut | ||
| + | | 90 | ||
| + | | 10 | ||
| | | | ||
|- | |- | ||
| − | |||
|bgcolor="#6699ff"|'''Holz''' | |bgcolor="#6699ff"|'''Holz''' | ||
|bgcolor="#99ccff"| Cut/Engrave | |bgcolor="#99ccff"| Cut/Engrave | ||
| Zeile 101: | Zeile 115: | ||
|bgcolor="#99ccff"| Speed | |bgcolor="#99ccff"| Speed | ||
|bgcolor="#99ccff"| Notes | |bgcolor="#99ccff"| Notes | ||
| + | |- | ||
| + | |Hartfaserplatte 4mm | ||
| + | |cut | ||
| + | |90 | ||
| + | |12 | ||
| + | | | ||
|- | |- | ||
| Zeile 106: | Zeile 126: | ||
| cut | | cut | ||
| 80 | | 80 | ||
| − | | | + | | 16 |
| | | | ||
|- | |- | ||
| Zeile 112: | Zeile 132: | ||
| Pappelsperrholz | | Pappelsperrholz | ||
| engrave | | engrave | ||
| − | | | + | | 40 |
| − | | | + | | 900 |
| | | | ||
|- | |- | ||
| Zeile 135: | Zeile 155: | ||
| cut | | cut | ||
| 90 | | 90 | ||
| − | | | + | | 2 |
| | | | ||
|- | |- | ||
| Zeile 151: | Zeile 171: | ||
| 800 | | 800 | ||
| | | | ||
| + | |- | ||
| + | |HDF 3.5mm | ||
| + | |cut | ||
| + | |90 | ||
| + | |9 | ||
| + | | | ||
| + | |- | ||
| + | |HDF 3.5mm | ||
| + | |cut | ||
| + | |40 | ||
| + | |1500 | ||
| + | |ritzen | ||
|- | |- | ||
| Zeile 169: | Zeile 201: | ||
| Acrylic (3mm) | | Acrylic (3mm) | ||
| cut | | cut | ||
| − | | | + | | 90 |
| − | | | + | | 15 |
| − | | | + | | war 80/25 hatte aber nicht so gute Erfahrung damit |
|- | |- | ||
| Zeile 193: | Zeile 225: | ||
| 10 | | 10 | ||
| | | | ||
| + | |- | ||
| + | |||
| + | | Acrylic (8mm) | ||
| + | | cut | ||
| + | | 90 | ||
| + | | 7 | ||
| + | | | ||
| + | |- | ||
| + | |ABS (1mm) | ||
| + | |cut | ||
| + | |90 | ||
| + | |30 | ||
| + | | | ||
| + | |- | ||
| + | |ABS (2mm) | ||
| + | |cut | ||
| + | |90 | ||
| + | |20 | ||
| + | | | ||
|- | |- | ||
| Zeile 215: | Zeile 266: | ||
| | | | ||
| | | | ||
| + | |- | ||
| + | |||
| + | | Styrodur (1,5 mm) | ||
| + | | cut | ||
| + | | 10 | ||
| + | | 400 | ||
| + | | Zwei Durchgänge, damit das Material in den Kanten nicht zu stark schmilzt. | ||
| + | |- | ||
| + | |Polystyrol (2mm) | ||
| + | |cut | ||
| + | |90 | ||
| + | |30 | ||
| + | | | ||
| + | |- | ||
| + | |Polystyrol (4mm) | ||
| + | |cut | ||
| + | |90 | ||
| + | |15 | ||
| + | | | ||
|- | |- | ||
| Zeile 235: | Zeile 305: | ||
| | | | ||
| | | | ||
| + | | | ||
| + | |- | ||
| + | |||
| + | | Jeans Denim | ||
| + | | cut | ||
| + | | 50 | ||
| + | | 100 | ||
| | | | ||
|- | |- | ||
| Zeile 268: | Zeile 345: | ||
| Porzellan | | Porzellan | ||
| engrave | | engrave | ||
| − | | | + | | 60 |
| − | | | + | | 1500 |
| − | | | + | | Fliesen |
|- | |- | ||
Aktuelle Version vom 17. April 2024, 12:58 Uhr
Materialeinstellungen
Alle Materialeinstellungen sind lediglich Richtwerte. Bitte immer einen Testschnitt machen und gegebenenfalls die Werte anpassen.
Faustregeln: Beim Schneiden Materialien die Schmelzen (z.B.: Acryl): Druckluft "No". Materialien die verbrennen (z.B.: Holz oder Papier): Druckluft "Yes".
Bitte nicht mehr als 90% Leistung einstellen. 100% Leistung überfordert die Laser-Röhre auf Dauer. Fokusiert wird mittels Autofokus. Der Abstandsmesser liegt 10mm vor dem Laserpointer => Aufpassen beim Fokusieren.
Die Einstellungen hängen vom Material, sowie der Sauberkeit der Linse und Spiegeln ab. Am besten vor dem Schneiden einen kleinen Testschnitt machen!
| Material | Cut/Engrave | Power | Speed | Notes |
|---|---|---|---|---|
| Papier & Karton | Cut/Engrave | Power | Speed | Notes |
| Finnpappe (1mm) | cut | 60 | 90 | |
| Finnpappe (1mm) | engrave | 20 | 90 | |
| Finnpappe (2mm) | cut | |||
| Finnpappe (4mm) | cut | |||
| Finnpappe (2mm) | engrave | |||
| Graupappe (0,5mm) | cut | |||
| Graupappe (1,5mm) | cut | |||
| Graupappe (2mm) | cut | 90 | 14 | |
| Graupappe (2mm) | engrave | 20 | 90 | |
| Graupappe (2,4 mm) | cut | |||
| Graupappe (3mm) | cut | 90 | 12 | |
| Graupappe (4mm) | cut | 90 | 10 | |
| Holz | Cut/Engrave | Power | Speed | Notes |
| Hartfaserplatte 4mm | cut | 90 | 12 | |
| Pappelsperrholz (4mm) | cut | 80 | 16 | |
| Pappelsperrholz | engrave | 40 | 900 | |
| Pappelsperrholz | Ritzen | 15 | 2000 | |
| Fichte 28mm | cut | 90 | 2 | |
| Sperrholz Pappel 6mm | cut | 90 | 2 | |
| Sperrholz Pappel 6mm | engrave | 30 | 1200 | |
| Sperrholz Pappel 6mm | Cut Schrift (Nur Umriss) | 30 | 800 | |
| HDF 3.5mm | cut | 90 | 9 | |
| HDF 3.5mm | cut | 40 | 1500 | ritzen |
| Kunststoffe | Cut/Engrave | Power | Speed | Notes |
| Acrylic (3mm) | engrave | |||
| Acrylic (3mm) | cut | 90 | 15 | war 80/25 hatte aber nicht so gute Erfahrung damit |
| Acrylic (5mm) | engrave | |||
| Acrylic (5mm) | cut | |||
| Acrylic (6mm) | cut | 90 | 10 | |
| Acrylic (8mm) | cut | 90 | 7 | |
| ABS (1mm) | cut | 90 | 30 | |
| ABS (2mm) | cut | 90 | 20 | |
| Acrylic | engrave | |||
| Laserply | engrave | |||
| Laserply (0,6 mm) | engrave | |||
| Styrodur (1,5 mm) | cut | 10 | 400 | Zwei Durchgänge, damit das Material in den Kanten nicht zu stark schmilzt. |
| Polystyrol (2mm) | cut | 90 | 30 | |
| Polystyrol (4mm) | cut | 90 | 15 | |
| Metall | Cut/Engrave | Power | Speed | Notes |
| Textilien, Leder, Filz, etc. | Cut/Engrave | Power | Speed | Notes |
| Filz 3 mm | cut | |||
| Jeans Denim | cut | 50 | 100 | |
| Stempel & Gummi | Cut/Engrave | Power | Speed | Notes |
| Glas | Cut/Engrave | Power | Speed | Notes |
| Standart Glas | engrave | |||
| Stein | Cut/Engrave | Power | Speed | Notes |
| Porzellan | engrave | 60 | 1500 | Fliesen |
| Organisches Material | Cut/Engrave | Power | Speed | Notes |
| Fun ;-) | Cut/Engrave | Power | Speed | Notes |